teekkürker karadağ.
Linkback: Ynt: Delta Pulse 2

yukarıda yazdığım potların çalışma şekli doğru mu? Hem birkez daha kaydedilmiş olur... saygılar

السلام عليكم
Thank you very much for your patience
But I am asking about these two resistances, where are they placed (RCOIL  &  RSONUM )
thank you

Alıntı yapılan: salem69 - 23 Ocak 2021, 22:28:38

السلام عليكم
Thank you very much for your patience
But I am asking about these two resistances, where are they placed (RCOIL  &  RSONUM )
thank you

Alıntı yapılan: BuLutBey - 28 Ocak 2021, 10:08:13

Alıntı yapılan: salem69 - 23 Ocak 2021, 22:28:38

السلام عليكم
Thank you very much for your patience
But I am asking about these two resistances, where are they placed (RCOIL  &  RSONUM )
thank you

Sorry . it was wrong

ADMİN ARKADAŞLAR MESAJI SİLE BİLİRMİ LÜTFEN

Bir an yanlış sandım  ama doğru yazmışım . bu pcb den yapmadım hiç yapan bilen ustalar daha iyi bilir.

Thank you very much, my Polish friend
Is it necessary to put this resistance in this way?

سلام عليكم
BULUTBEY


Sorry brother I wrote your name is not correct
I am  very sorry

I added diode STTH1210D between PIN 2 of IRF and coil, and 10kohm between two PIN 1 and 3 of IRF

[size=78%] سلام عليكم [/size]
[/size][size=78%]صنعت ملف بحث ل delta pulse 2 بقطر 50 سنتمتر لكني لففته بالياف زجاجيه  لعدم تاثر الملف بالشحنات الخارجيه [/size]
[/size][size=78%]هل ما فعلته صحيح و لا يؤثر على لفائف [/size]
[/size][size=78%]شكرا لكم [/size]

 
I made the coil with a diameter of 50 cm, the resistance was 2.7 ohm and the inductance was 390, but I wrapped the coil with glass fiber. Is what I did correct?

Alıntı yapılan: salem69 - 24 Mart 2021, 00:04:30

I made the coil with a diameter of 50 cm, the resistance was 2.7 ohm and the inductance was 390, but I wrapped the coil with glass fiber. Is what I did correct?

I think will not be problem.

Hello
A problem occurred with Delta 2 ... which is that the device does not make any sound when operating (and the sound appears when you make the NOISE at the highest level) and the device starts with good detection, but it quickly decreases the level of detection until it does not reveal that the metal sticks to the search coil ... What is the reason for this The problem please

Hi,

Did you test it with manuel tune? Is there same problem?

HELLO
YES I TEST IT

السلام عليكم
شكرا لك صديقي الجبل الاسود ارجو منك مساعدتي
و انا ممتن منك

Alıntı yapılan: salem69 - 03 Haziran 2021, 21:53:19
السلام عليكم
شكرا لك صديقي الجبل الاسود ارجو منك مساعدتي
و انا ممتن منك

This means your oscillator is not working. You must examine 556 circuit.

Hello
God willing, you will be fine
I want to know the value of the headset
And I want to know how to connect the headphone and what is its value

Alıntı yapılan: salem69 - 18 Haziran 2021, 11:33:18

Hello
God willing, you will be fine
I want to know the value of the headset
And I want to know how to connect the headphone and what is its value

You can use standart headset. There is no extra value. There is headphone pin on the PCB. You can connet directly to there.

Alıntı yapılan: kato - 12 Mart 2015, 00:06:38
hello masters, I once made a model of delta pulse, I am attaching its photo. It worked
well but the setting was very problematic and I was making it difficult,
so I put it aside, now I looked around the site and looked at who models.
It has very few buttons. Can I reduce the buttons of this?
thank you all

which diagram do you use?