Delta Pulse 3 Dijital Pulse Dedektör

[Karadağ]

We are not giving hex file. We are uploading the hex to a pic and sending to hobbyists.
Linkback: Ynt: Delta Pulse 3 Dijital Pulse Dedektör

[wodekj7]

Bu etkinliği çok severim. Bu etkinliği yaptım. Maalesef, demo sürümüydü. Tam sürümüne ihtiyacım var.

[wodekj7]

我可以购买完整版的十六进制文件吗

[wodekj7]

Arkadaşlar merhaba, Delta Pulse 3 mikroprosesör çipini resmi web sitesi üzerinden nasıl satın alabilirim, bağlantıyı bulamıyorum.

[wodekj7]

Delta Pulse 3, 2×2 metre'lik bir bobin kullanabilir mi? Detaylı parametreleri nelerdir?

[Kürşat]

Kullanılır 70lik bobin yeterli ama

[wodekj7]

1：电路卡有时有0.65V有时1.71V电压，这是正常的吗？如何解决？
2：标题频率为180 Hz。
3：安装控件线圈时，没有振动，并且屏幕不会显示幽灵。
4：我看不到屏幕曲线。

[Zanos]

1：电路卡有时有0.65V有时1.71V电压，这是正常的吗？如何解决？
2：标题频率为180 Hz。
3：安装控件线圈时，没有振动，并且屏幕不会显示幽灵。
4：我看不到屏幕曲线。

Türkçe ya da ingilizce yazabilir misiniz.

[wodekj7]

1: LCD ekrandan ekran spektrumu ve eğrileri göremiyorum.

[wodekj7]

Daire içindeki VD15 ve R72'yi kısa devre edebilir miyim? Sadece kısa devre yapıldığında 1.6V görürüm.

[wodekj7]

Yarıncilikli hocalar bana yardım edin, neredeyse çökmekteyim. Yarı yıl过去了 (半年) hiçbir ilerleme yok, 3 adet PIC chip yakıldı.
Devre voltajı normal, frekans da her zaman 249hz.
Bobin bağlanmadığında OSC menüsü图1.2'yi (Figure 1.2) gösteriyor.
Bobin bağlandığında图3'ü (Figure 3) gösteriyor.

[wodekj7]

Yarıncilikli hocalar bana yardım edin, neredeyse çökmekteyim. Yarı yıl过去了 (半年) hiçbir ilerleme yok, 3 adet PIC chip yakıldı.
Devre voltajı normal, frekans da her zaman 249hz.
Bobin bağlanmadığında OSC menüsü图1.2'yi (Figure 1.2) gösteriyor.
Bobin bağlandığında图3'ü (Figure 3) gösteriyor.

[Zanos]

Merhaba,

Sönüm eğrisini biraz daha ayarlayın. Bir de algılama sinyalini kontrol edin.

[Zameer12]

I have created this c source code with AI for Delta Pulse 3. Can you tell me if this source code is correct according to the circuit?

I know that it is not right to make a C source code for someone else's circuit. But I am forced. I have made this circuit, so I had to make the C source code too.

Please sir if you can give me information about the pins of PIC18f452 then it will be greatful

I made this circuit on the request of a person. That person told me to make the circuit. And when you make it, then he told me that he will send me the source code. But 4 to 5 years have passed and he has still not sent the source code.


At present UI is not fully ready. But the problem is not with UI, UI will be fixed with update. The problem is with PIC pins, it is difficult to understand them. Which command, which logic has to be set on input pins and output pins, that is the biggest problem for me.

[Zanos]

I have created this c source code with AI for Delta Pulse 3. Can you tell me if this source code is correct according to the circuit?

I know that it is not right to make a C source code for someone else's circuit. But I am forced. I have made this circuit, so I had to make the C source code too.

Please sir if you can give me information about the pins of PIC18f452 then it will be greatful

I made this circuit on the request of a person. That person told me to make the circuit. And when you make it, then he told me that he will send me the source code. But 4 to 5 years have passed and he has still not sent the source code.


At present UI is not fully ready. But the problem is not with UI, UI will be fixed with update. The problem is with PIC pins, it is difficult to understand them. Which command, which logic has to be set on input pins and output pins, that is the biggest problem for me.

Hi,

This code is not understandible clearly. Did you try to buil it? And which builder program are you using?

[Zameer12]

No. I have not tried the c source code. Because I do not have information about the pins. Can you help me? Which pin is giving output and which pin is giving input.And what is the function of these pins and which command needs to be set This will make it easier for me to write its logic.

[Zameer12]

This is the new C source code. In which I have made some updates. I have not tested it in circuit. But I have tested it using breadboard. If you want, you can make it even better. But I think there is still a logic problem in it. The problem is setting the correct command.
If you want, you can test it using breadboard
This is the LCD and PIC connections and this is KS0108

LCD PIN 7 (D0) = PIC PIN 19 (RD0)

LCD PIN 8 (D1) = PIC PIN 20 (RD1)

LCD PIN 9 (D2) = PIC PIN 21 (RD2)

LCD PIN 10 (D3) = PIC PIN 22 (RD3)

LCD PIN 11 (D4) = PIC PIN 27 (RD4)

LCD PIN 12 (D5) = PIC PIN 28 (RD5)

LCD PIN 13 (D6) = PIC PIN 29 (RD6)

LCD PIN 14 (D7) = PIC PIN 30 (RD7)

LCD PIN 15 (CS1) = PIC PIN 37 (RB4)

LCD PIN 16 (CS2) = PIC PIN 36 (RB3)

LCD PIN 5 (RW) = PIC PIN 39 (RB6)

LCD PIN 4 (D/I) = PIC PIN 40 (RB7)

LCD PIN 6 (E) = PIC PIN 38 (RB5)